(Quoted) a 2016 yaris all key lost, I manage to unlock it with va6
lishi and read the barrel but i can’t turn the ignition with va6 lishi.
then I bought va8 lishi and voila you can pick and read the ignition. I
have sec-e9 cutting machine and I can’t cut the blade.
the only option is 2016 corolla in SEC-E9 Key Cutting Machine…..8 wqafers depths 1, 2, 3, 4, but I still can’t cut the blade because what I read from the va8 lishi doesn’t match.
Finally, used silca futura machine to cut the blade, the job is done
now. but it will be difficult for me to call my buddy just to cut the
blade every time. The silca futura is bloody expensive. The next parts
answer a question: how to cut this new blade with sec-e9 or other
machine?
I have the xhorse condor. There is a CustomKeyTools.
Create your own key file, and load that in your machine.
Have a look at the condor keycutter thread.
series exists in instacode if your machine can work with instacode or if you can make your own cutting card .
Question: I tested with sec-e9 toy51 add manually key turn on door but not ignition ! Have you an idea ?? Please
Answer: 1. you have wrong cuts somehow
2. ignition has been changed
3. door has been changed
I just copy with manual cutting machine most new blades.
For your information: va8? va6? any difference?
When the va6 and the va8 tools were made there was no specific reference for these , all 3 use the same VA2 keyblade .
yes the va8 is for the 1234Q5678H series with 8 cuts , it will also
do the daf cf series 7 cut lock as well , it will also do the VA6 6 cut
models though will be sloppy decode due to extension .
the question was what key blade as va8 not listed in silca which it
wont be as a lishi reference not a key blank reference , the blade is
va2 all are listed under VA2 in instacode ;
ic : 1049 for the 6 cut ABCDEF series
IC : 1125 for 6 cut 1234Q5678H series
IC : 1126 for 6 cut 1234Q5678H series
IC : 1423 for 8 cut 1234Q5678H series
not all lishi tool refrences relate to silca references as quite
often a tool is developed long before silca assign a key blank reference
to it , good examples are ‘
HU100R
vag2015 8 , 9 and 10 cut
va6
va8
H & Q have no meaning to you if reading lock with a lishi tool ,
they are values that are used in the dealer code under certain
conditions .
when 2 x 4 cuts sit next door to each other they change them to QQ , 2
x 8 cuts sat next door to each other change to HH , a 4 cut and an 8
cut sat next door to each other change to Q and H .
so if you read a lock as 673784 , the manufacturers code would read
QH7376 , if entering direct cuts you reverse this to 6737HQ or 673784
both cut the same key
so you can enter Q or 4 and you can enter 8 or H it will still cut the same
We will install the software before ship, so you can get it work directly after you receive it.
2019A Caterpillar ET Software as Cat Caterpillar ET 2018A Software update version, 2019A Caterpillar Electronic Technician softwarer With CAT ET 3 Cat caterpillar adapter 3 support caterpillar diagnostic till 2019.
Cat et Caterpillar Electronic Technician Software 2019A V1.0: Type of catalogue: Caterpillar Electronic Technician Diagnostic Software Make: Caterpillar Region: WorldWide all region
CAT Caterpillar ET Diagnostic Tool from Caterpillar provide the capability to access Electronic Control Modules (ECMs) from a personal computer. Many job-critical tasks can be performed with an electronic service tool. The user can display the status of a group of parameters (temperatures, pressures, etc.) simultaneously, view active and clear logged diagnostics, display the current configuration of an ECM and much more. The service tool works with a communication adapter to allow connection to an ECM. A graphical interface makes this software quick to learn and easy to use. A separate pull-down menu for each function enhances the “ease of use.” The version and identification of the ECM is automatically retrieved and is displayed on a summary screen when the program is started. Diagnostic tests and calibrations can also be performed.
CAT Caterpillar ET Diagnostic Tool enable service technicians to reprogram ECMs, reconfigure control system parameters, fine tune performance or diagnose the root cause of a failure the first time. These powerful tools allow service personnel to display and analyze vital performance and health information from any system quickly and accurately. The service tool communicates with any system using ATA (J1708), J1939 or the Caterpillar proprietary data link networks. The service tools provide information and features needed to help a technician diagnose problems and perform repairs and to customize and personalize the operation of a product. By allowing customers to design flexibility and configurability into a product, Caterpillar service tools stretch beyond the capabilities of preprogrammed ECMs or onboard display systems.
Features
Display, graph and log status parameters.
Retrieve prognostic data including histograms, engine totals for fuel used and miles traveled.
View active diagnostics and clear logged diagnostics. View events where irregularities have occurred and have been logged by the ECM. Perform calibrations to enhance performance of the ECM. Customize the ECM with application-specific settings. Over 100 custom Diagnostic, Information and Service features including: – 2D and 3D Histogram plotting capability (engine software support required). – Custom Status screen groups – Snapshots (Download and display snapshot data recorded by the ECM) – Configuration Aid that allows upload/download of same configuration to multiple control modules
Customised Service Tool Options Customized service tool name Customized graphics for the splash screen and icons Customized installation Aftermarket differentiation, i.e., the tool for one customer does not work on the product of another customer. Licensing options for customer management Flash programming of the ECM(s) Training demonstration allows familiarity with the tool’s primary functions without connecting to ECM(s)
Perform customized diagnostic tests to identify harness problems, cylinder or component failures (Automatic Cylinder Cutout with cylinder to cylinder fueling comparison)
Caterpillar ET Software 2019A Function: This diagnostic app allows you to: View active and logged diagnostics. View events where irregularities occurred and were logged by the ECM. View the status of a group of parameters (temperatures, pressures, etc.) simultaneously. Record and log performance data. Graph a group of status parameters. View the current configuration of an ECM. Change ECM configurations. Perform diagnostic tests. Perform calibrations. Print reports and diagnostic results. Please keep in mind that some ecm settings for example, speed limit requires factory password. The factory password generator is not included in this application
Original Factory Caterpillar ET3 Adapter III Compare With OEM Caterpillar ET Diagnostic Adpater III 1. Original Factory CAT ET can use once pluged, no need install the USB drive, the software can automatic realize it for ET3 Adapter, and the machine can automatic weld the high quality Circuit board, quality will be more reliable.
2. The OEM Caterpillar ET Diagnostic Adapter III need use USB Drive to install, and need choose the COM Port, and in the software ET also need choose ET2 then can be used.
CAT Caterpillar ET Diagnostic Adapter III Main Board
Hardware
Package 1 : 1.Used Dell D630 laptop 2.Real CAT et3 Comm Adapter III(it’s best quality cat et 3,not adapter 2,please check Communication port) 3.USB Cable (From device to your computer) 4.J1939/J1708 9PIN Cable (from device to your truck) 5.6PIN Cable (for old truck)
Package 2: 1.Used Dell D630 laptop 2.Real CAT et3 Comm Adapter III(it’s best quality cat et 3,not adapter 2,please check Communication port) 3.USB Cable (From device to your computer) 4.J1939/J1708 9PIN Cable (from device to your truck) 5.6PIN Cable (for old truck) 6.14PIN Cable(for new truck,optional)
What’s New
What’s New – 2019A
ECM Naming Changes
Certain ECMs connect to the service tool over two data links at the same time. The service tool shows a message popup when the ECM is only detected on one link. The service tool has been changed to add the text **INCOMPLETE** in the ECM name when the connection is incomplete. Service tool features that display a connection icon also use a new icon for an incomplete connection.
What’s New – 2018C
No significant new features or feature enhancements
What’s New – 2018B
CEOS Fleet Configuration File TOP
A CEOS (Customer Electronic Option Selection) Fleet Configuration File can be created/modified for an engine using the Service Tool. This is available in connected and disconnected mode.
Error When Launching Service Tool
There is a Microsoft issue with upgrading libraries during an installation involving certain versions of the C++ redistributable. After a successful service tool installation, when trying to run the service tool for the first time, one of the following errors may occasionally appear: “The entry point could not be located in api-ms-win-crt-runtime” or “The program can’t start because mfc140u.dll is missing from your computer.” If either of these messages is displayed, please let us know and we will send you to step by step troubleshooting guide. This procedure requires administrator rights.
Service Tool License Corruption Issues with Windows 10 Updates
Windows 10 updates 1709 and 1803 will corrupt service tool licenses. Future Window 10 updates may do the same
If either of license error messages is displayed, please let us know and we will send you to step by step troubleshooting guide.
What’s New – 2018A
Trainer Update – 988K XE Wheel Loader
The 988K XE Wheel Loader has been added to the Trainer application.
What’s New – 2017C
Preferences Option to Save a Product Status Report to PDF
The Preferences dialog for the Product Status Report has changed. The dialog contains a new checkbox to automatically save a Product Status Report as a PDF file when the report is created. The service tool will continue to automatically save Product Status Reports as an XML file.
What’s New – 2017B
Product Status Report Updates
The Product Status Report has been updated to include certain history features supported by the ECM, such as the after-treatment Regeneration History and the Service Test History.
Winflash Screen Update
The screen for the Winflash feature has been updated. A new Expand All button opens all sections of the screen to show all details for ECMs detected by WinFlash. A new Collapse All button hides all sections of the screen, except for header rows showing detected ECM names.
PC, Communication Hardware, and Cable Requirements
To run the service tool, the next PC, communication hardware, and cable requirements must be met. NOTE: The minimum PC Configurations should not be used as a standard when buying new personal computers for service tool purposes. If the existing equipment meets these minimum requirements, it will run the service tool.
PC Requirements
Recommended Configurations
PC containing a 2.0 GHz dual-core processor
3GB RAM
3GB of the available hard disk drive
DVD-ROM drive (optionally)
15.4-inch XGA Screen (1280×1024 compatible)
Microsoft Windows? 7 Professional or Windows 8 Professional, Windows 10 Professional (Not tested with Home Edition) (Note: Windows 8 RT is not supported)
RS232 port with 16550AF UART or compatible (for use with Comm Adapter II)
USB 1.1 or 2.0 port (for use with Comm Adapter 3)
Ethernet RJ45 connector
Built-in pointing device or mouse
For security purposes, Microsoft Internet Explorer version 11 or newer or Microsoft Edge is recommended.
Note: The most recent version of Microsoft? Internet Explorer may not be validated to work with the service tool.
Wi-Fi (for the Wireless Comm Adapter 3)
Minimum Configurations
PC containing a Pentium 2 GHz processor or greater
1GB RAM
500MB of an available hard disk drive
CD-ROM drive
Super VGA monitor or display (1024×768)
Microsoft Windows? 7 Professional or Windows 8 Professional, Windows 10 Professional (Not tested with Home Edition) (Note: Windows 8 RT is not supported)
RS232 port with 16550AF UART or compatible (for use with Comm Adapter II)
USB 1.1 or 2.0 port (for use with Comm Adapter 3)
Ethernet RJ45 connector
Built-in pointing device or mouse
For security purposes, Microsoft Internet Explorer version 9 or newer is recommended. Note: The most recent version of Microsoft? Internet Explorer may not be validated to work with the service tool.
Communication Hardware
Caterpillar Communication Adapter III
Configuring Cat Electronic Technician to use the Communication Adapter 3
For Cat Electronic Technician to work with the Communication Adapter 3, the settings must be changed to select the Communication Adapter 3 as the Communication Interface Device:
Step 1 Start Cat Electronic Technician.
Step 2 Click the Stop Connect button when it appears.
Step 3 Select the Utilities menu.
Step 4 Choose “Preferences > Modify…”.
Step 5 Select the Communications tab.
Step 6 Select Cat Comm Adapter 3 (RP1210) and click OK.
NOTE: Because a growing number of products require multiple data link service, the “Enable Dual Datalink Service” checkbox has been pre-selected.
Servicing ECMs on more than one data link requires this check box to be enabled.
Failure to do this will result in undetected ECMs and reduced functionality.
