How to Fix Yanhua 35XX Emulator 36150WT Red Dot Problem?

One of our customers reported that he used Yanhua 35xx simulator for BMW 6WB 35160WT cluster, he had a red dot on cluster and mileage display 999999km after replacing eeprom.

Images attached:




Here is the possible solution:

BMW dashboards from August 2015 are equipped with a 35160WT/35128WT EEPROM which is not erasable and has page-id which locks this memory to its own dashboard-micro. If you need to correct such dashboards you CANNOT erase or substitute the original memory with recovered/bought one. You have to emulate the original memory with Yanhua YH35XX Programmer + Simulator. The independent programmer comes with software inside. The software can be run directly when the programmer is connected to PC.



In this case, the original chip is 35160WT, after replacing it with the small 35xx simulator, the dash shows 99999km, the 8th pin of the original 35160WT should be 5V which causes the small 35xx emulator to burn, so you will need a larger 35xx simulator chip.

If the 8th pin of the 35160WT chip is 5V, you need another simulator chip (bigger one), which is compatible with both 35128WT and 35160WT. Replace eeprom with the bigger simulator should be fine.

Nissan Consult 3 Plus V235 Software for VXDIAG Download Free

New version Nissan Consult III Plus V235 was tested working with VXDIAG scanners without issue.





Software version: Nissan Consult 3 Plus V2335

Compatible devices: VXDIAG VCX NANO Nissan, VXDIAG VCX SE Nissan

Operating system: Win10

Multi-language: Chinese, Russian, Spanish, Turkish, Thai, Czech, Polish, Finnish, French, German, Greek, Italian, Japanese, Portuguese, Hungarian

Patch/Loader: Yes, software uses patch. Software contains patch for vxdiag.

Driver: This version requires latest Nissan RNM VCI driver support. Install Nissan VCI driver for Consult3-P in vx manager. Don’t need to install driver separately anymore.


Free Download VXDIAG Nissan Consult 3 Plus V235 software

Download LINK



The software and patch are used with VXDIAG ONLY.



Start C3+P software from loader. Check VI device status.

How to Fix Launch CRP919X CRP919E Screen Flashing?

One of obdii365.com’s customers reported that his Launch CRP919E BT scanner screen flashed after turning on.

Image attached:




Possible reason:

Screen cable of the machine is detached.



How to install screen cable?

If your Launch CRP919X BT, CRP919E, CRP919X series screen flashes, do the same procedure to install screen cable.



1. Remove the screws from the back cover of the scanner.
2. Remove the speaker cable and remove the back cover.
3. Clean the compressed foam and acetate tape.
4. Find the power strip and reconnect the screen cable.
5. After testing the device screen and seeing that it is normal, reassemble the device in the order of disassembly.

Tips to Learn 2020 Opel 4A Smart Key with Autel IM608

Problem:

Tried to learn spare key Opel Corsa F from 2020 by Autel IM608 without success.
I did read pin code. But when tried to learn key get message try again after 2 min.
Any idea?


Solution:

It’s 4A Key. You have to enter with Peugeot.
Read pin code after adding key.
Learn key under Peugeot not under Opel.

If still fails to learn key, leave ignition on with the hazards on too for 30 mins until the hazards stop flashing then try.

www.obdii365.com

Godiag GT100 Pinout to Chevrolet Cobalt LT ECM

I have a 2008 Chevrolet Cobalt LT. I started researching making my own bench harness but that led me to finding the GODIAG GT100 device. It allows you to connect to any PCM/ECM outside of the vehicle. This is useful for ECM troubleshooting, diagnostics, coding and programming. I'm not sure how much I will use it but certainly useful for my current set of problems. Worked like a charm. For reference, I connected 12v power leads to pins 3,19, 20 and 73, CAN- to 43 and CAN+ to 44 on J1 and ground to pin 73 in J2 (2008 ECM). Connect scanner to OBD2 and bam, I'm able to pull codes and read information directly from the ECM. Hope it helps someone out there!