Cell Phone spare parts online - ETrade Supply

https://www.etradesupply.com/

3 Steps on How to Replace OnePlus 6 Rear Camera Lens Cover

2020-01-16 16:00:51 | OnePlus

The OnePlus 6 camera lens cover is easy to be scratched and broken. When this happened unfortunately to your phone, we suggest you replace it. It is not good to replace the camera lens cover directly on the back cover because it will leave fragment or fingerprint on the camera. Here we would like to demonstrate how to tear down the battery door and replace the camera lens cover in steps. Let’s check this below.

 

Step 1: Tear down the battery door

First of all, we should always remember to power off the phone and take out the SIM card slot. Use a hot air gun to blow the battery door on around the edge on 80 ℃ for 1-2 minutes for easy teardown, then use a suction cup and hard plastic plectrum to slice and separate the battery door. Flip over the battery door after it is entirely separated. Loosen the 10 Phillips screws and take off the bracket, then we may disconnect the fingerprint scanner sensor.

Step 2: Take off the Camera lens and replace the lens cover

After the OnePlus battery door is totally separated, we can move to the next step on camera lens cover replacement. Firstly, we use a hot air gun to blow the camera lens with 80℃ for 1 minute. After the glue is melted, use a spudger to push the camera lens cover out. Next, we use an ultra-thin plastic sheet to slice and separate the OnePlus 6 rear camera lens cover from the battery door. After the camera lens cover is removed, we have to clear out the glue on the battery cover. Glum the camera lens with B-7000 glue and place the new camera lens cover on it. Push it slightly and adjust the position.

Step 3: Reassemble the battery door

After the new camera lens cover is installed, we have to test the clarity of the new glass cover. Attach the battery door on the phone and turn on the phone. Turn on the camera and check the image on the screen. Make sure no dust, dirt or fingerprint on the camera. Then take off the battery cover, attach a new frame cover adhesive on the battery door. Connect the fingerprint scanner sensor flex cable and cover back the bracket. Fasten the 10 Phillips screws. The Last step, assemble the OnePlus 6 battery door and insert the SIM card tray. All process is done.

 

The whole process is simple as long as you are careful. Don’t take off the camera lens cover from the battery door directly because it will break the glass cover and leave fragments on the camera. If you are not confident about yourself, we suggest you go to the repair shop. Besides, you may also check the OnePlus 6 parts like OnePlus 6 LCD screen and digitizer assembly in our store. Leave your message to us if you have interests. Etrade Supply is here to help you.
 

How to Choose A screen Protector for Your Phone?

2020-01-09 19:01:58 | mobile phone accessory

A good screen protector could be a shield for your mobile device’s screen protection. Much more than this, some new screen types could upgrade your screen image tone and make your phone in a good look. Since there are all kinds of mobile phone screen protectors in the market, choose a suitable one for your phone is important. Here we discuss how to choose a screen for your smartphone, we hope this would be helpful to you if you are going to applying one on your phone.

Here we come up with four screen types based on different raw materials. The first type is PET plastic. Screen protectors made of PET plastic is light and thin, and also cheap. The transparency of this screen protector is good, but the flexibility is bad. It cannot go edge-to-edge on phones with a curved screen. The second type is TPU plastic. The TPU plastic material is flexible, waterproof, oil resistance and antibacterial. This screen protector faces many issues when it first comes to the market, such as hard installation, unsmooth, "orange peel" type glare to your phone's screen. With the technology upgraded, these issues were gone. TPU screen protector is welcomed by users now. The tempered glass screen protector is the one we used most, we can take the iPhone 11 tempered glass screen protector as an example. Since the tempered glass screen protector is hard and strong with better transparency, it is a hot sell type in the market. The last type we have to mention is the Nanometer multi-layered screen protector. This is a new kind of screen protector which is manufactured under high technology and Nanometer thickness material. Each layer of the screen protector functions differently, for which the screen protector could be anti-spy, anti-glare on the surface or smudge resistance. Such kind of screen protector is quite expensive on the market.

Since we have mentioned the four most usual screen protector above, it is suggestible to check the suitable wholesale mobile phone screen protector online. We have to understand what purpose we need to apply a screen protector on our phone screen. Besides, we have to know our smartphone brand and the model number so that we can search for a suitable one. You may also go to our Etrade Supply online store for our new coming iPhone tempered glass screen protector if you have interests.