killtestはHP Certification III 認証の最新問題集を提供いたします、最も標準的な技術を正確的に書き入れ、認証した専門家と作者の出版した新製品だけを使います、HP Certification III 認証のHP0-238問題集は世界のどこでも人気があるんですよ、killtestでその問題集を購入するのは明確の選択でございます。
HP0-238
1.Click the Exhibit button. Which LED on the MSA1000 controller indicates a failure on a
configured hard disk?
A.LED 9
B.LED 15
C.LED 16
D.LED 17
Correct:B
2.The MSA1000 controller display module can hold up to 100 messages. Once the maximum is
reached, the older messages will be ____.
A.copied to the connected host using ACU-XE
B.copied to the connected host using the serial line
C.deleted
D.copied to the connected metadata part of the disks
Correct:C
3.The customer has a single controller MSA1000 configuration. What is the recommended action
to replace the failed controller?
A.Power down the MSA1000. Remove the failed controller and install the old cache module in the
replacement controller.
B.Push the right arrow push button on the front panel to clear the cache of the controller and replace the
failed controller.
C.Replace the failed controller online, with a new cache installed.
D.Push the left arrow push button on the front panel to clear the cache of the controller and replace the
failed controller.
Correct:A
4.What is the recommended action to take when a controller fails in a redundant MSA1000
configuration?
A.Power off the MSA1000 and replace the failed controller.
B.Replace the failed controller online.
C.Push the right arrow push button on the front panel to failover the controller and replace the failed
controller.
D.Modify the zoning so that the MSA1000 is not accessible during the online replacement of the failed
controller.
Correct:B
5.Click the Exhibit button. The EMU in a MSA1000 has detected a temperature problem. Which
LED of the enclosure status indicators reports the problem and how does the LED display the
error condition?
A.LED 1 is off.
B.LED 2 is amber.
C.LED 3 is off.
D.LED 3 is amber.
Correct:D
6.Click the Exhibit button. Which LED on the MSA1000 controller indicates an error message was
sent to the controller display?
A.LED 9
B.LED 15
C.LED 16
D.LED 17
Correct:D
7.You are assigning DISK109 as a spare drive to array B containing logical drives 2 and 3. What is
the correct CLI (command line interface) command?
A.ADD SPARE UNIT=2 DISK109
B.ADD SPARE ARRAY B DISK109
C.SET SPARE ARRAY B DISK109
D.SET SPARE UNIT 3 DISK109
Correct:A
8.Click the Exhibit button. On an MSA1000 disk, LEDs 1 and 2 are OFF, and LED 3 is ON. What is
the possible cause for the status and which action should you take?.
A.The drive is part of the selection of the array configuration utility. Do not remove this drive without
verifying the configuration.
B.The array is rebuilding. Do not remove this drive without verifying the configuration.
C.The array is performing an online expansion. Do not remove this drive without verifying the
configuration.
D.The drive failed and has been taken offline. You can remove the drive.
Correct:D
9.You are replacing a defective power supply in a redundant MSA1000 configuration. Which
statement is correct?
A.Remove the power supply. Note the part number of the unit and order the replacement part. Install the
replacement part when it arrives.
B.Power off the MSA1000 during replacement to reduce the risk of personal injury.
C.Replace both power supplies at the same time because they contain the cache battery assembly.
D.Removing a power supply significantly changes the airflow in the cabinet. The remaining power supply
will shutdown the array after 5 minutes.
Correct:D
10.The customer has a redundant MSA1000 configuration. Identify the correct statement about
replacing an array accelerator (cache) module.
A.The array accelerator modules in both controllers must be the same size.
B.The array accelerator module can be replaced by a larger one. The extra space will not be used.
C.The array accelerator module can be replaced by a smaller one. The cache will be switched off.
D.If you have only different size modules available, you must power off the array during replacement.
Correct:A
HP0-238
1.Click the Exhibit button. Which LED on the MSA1000 controller indicates a failure on a
configured hard disk?
A.LED 9
B.LED 15
C.LED 16
D.LED 17
Correct:B
2.The MSA1000 controller display module can hold up to 100 messages. Once the maximum is
reached, the older messages will be ____.
A.copied to the connected host using ACU-XE
B.copied to the connected host using the serial line
C.deleted
D.copied to the connected metadata part of the disks
Correct:C
3.The customer has a single controller MSA1000 configuration. What is the recommended action
to replace the failed controller?
A.Power down the MSA1000. Remove the failed controller and install the old cache module in the
replacement controller.
B.Push the right arrow push button on the front panel to clear the cache of the controller and replace the
failed controller.
C.Replace the failed controller online, with a new cache installed.
D.Push the left arrow push button on the front panel to clear the cache of the controller and replace the
failed controller.
Correct:A
4.What is the recommended action to take when a controller fails in a redundant MSA1000
configuration?
A.Power off the MSA1000 and replace the failed controller.
B.Replace the failed controller online.
C.Push the right arrow push button on the front panel to failover the controller and replace the failed
controller.
D.Modify the zoning so that the MSA1000 is not accessible during the online replacement of the failed
controller.
Correct:B
5.Click the Exhibit button. The EMU in a MSA1000 has detected a temperature problem. Which
LED of the enclosure status indicators reports the problem and how does the LED display the
error condition?
A.LED 1 is off.
B.LED 2 is amber.
C.LED 3 is off.
D.LED 3 is amber.
Correct:D
6.Click the Exhibit button. Which LED on the MSA1000 controller indicates an error message was
sent to the controller display?
A.LED 9
B.LED 15
C.LED 16
D.LED 17
Correct:D
7.You are assigning DISK109 as a spare drive to array B containing logical drives 2 and 3. What is
the correct CLI (command line interface) command?
A.ADD SPARE UNIT=2 DISK109
B.ADD SPARE ARRAY B DISK109
C.SET SPARE ARRAY B DISK109
D.SET SPARE UNIT 3 DISK109
Correct:A
8.Click the Exhibit button. On an MSA1000 disk, LEDs 1 and 2 are OFF, and LED 3 is ON. What is
the possible cause for the status and which action should you take?.
A.The drive is part of the selection of the array configuration utility. Do not remove this drive without
verifying the configuration.
B.The array is rebuilding. Do not remove this drive without verifying the configuration.
C.The array is performing an online expansion. Do not remove this drive without verifying the
configuration.
D.The drive failed and has been taken offline. You can remove the drive.
Correct:D
9.You are replacing a defective power supply in a redundant MSA1000 configuration. Which
statement is correct?
A.Remove the power supply. Note the part number of the unit and order the replacement part. Install the
replacement part when it arrives.
B.Power off the MSA1000 during replacement to reduce the risk of personal injury.
C.Replace both power supplies at the same time because they contain the cache battery assembly.
D.Removing a power supply significantly changes the airflow in the cabinet. The remaining power supply
will shutdown the array after 5 minutes.
Correct:D
10.The customer has a redundant MSA1000 configuration. Identify the correct statement about
replacing an array accelerator (cache) module.
A.The array accelerator modules in both controllers must be the same size.
B.The array accelerator module can be replaced by a larger one. The extra space will not be used.
C.The array accelerator module can be replaced by a smaller one. The cache will be switched off.
D.If you have only different size modules available, you must power off the array during replacement.
Correct:A