Best Budget Sliders? : sevenoak camera slider

　　In general, only professional videographers will buy camera slider exclusively. Daily video shooting do you want to have a camera slider made its own? Today I bring you a professional camera sliderDIY production process, the cost will not be more than 3 soft sister coins, the shooting effect is absolutely not lose big. Smart tricks buddy move it!

　　Polished brass polishing

　　The first thing to do is to make the camera slider track, where I use a 3-meter long, 22-mm-diameter copper standard. The length and diameter of the pipe can be adjusted according to their own needs, where I will be the same length of brass saw saw two spare.

　　Oxidation will make the brass look dirty, then clean it with metal and soapy water can be easily done. Of course, we can also apply a layer of metal paint on the copper tube to prevent oxidation, liquid paint can be, but need to brush twice.


　　Ready to make medium fiberboard

　　The production of several MDF is mainly to connect two steel pipes, but also for the production of back to bring a lot of convenience.

　　Material selection 6 mm thick MDF, because it is cheap, hard texture. The template will be printed out with a double-sided adhesive tape on the edge of 12 square meters of square fibreboard, punched in the mark. In order to ensure accuracy, with 1 mm drill bit drilling, and then replaced by 4 mm drill bit, the middle hole requires 9 mm drill bit to drill. After you get it, saw the excess part saw with a saw, and then sanding, spray black paint moment big. Such a template to do two, on both ends, in the middle of a bigger piece.

　　In order to slide freely back and forth, we need to open the top two holes.

　　Punch requires a secret weapon, first with plasticine copper tube fixed in the plane, and then mark where needed to punch. Here to share a little secret: we can not use the original multi-layer MDF overlay, in front of the MDF slightly overlay, the rear two layers thicker (smaller area), and then tied to a manual knife (see Video 3 minutes and 49 seconds).

dslr camera slider
video camera slider
dslr camera cage
gimbal tripod head
tripod head
camera viewfinder
jib arm
camera dolly

Sevenoak Camera Dolly and Camera Dollies for Sale

　　This is definitely a skateboard photographer essential products! Although there are sold everywhere, but this is the exclusive slider! Teach you to DIY a photographic car! The tool is very simple, discarded board and a wheel can handle It!

　　1, camera Dolly can be loaded 100MM bowl PTZ (standard) and 150MM bowl PTZ (optional), can be adapted to all movie-level cameras or TV cameras.

　　2, Camera Dolly imported rubber wheel, smooth and smooth operation, ultra-quiet!

　　3, the track using 3CM pipe, wall thickness 7MM, CNC machining technology, so you impeccable. Track single section 60CM,

　　The standard package can be stitched up to 2.4M, for longer, more matching two 60CM track can be.

　　4, rail car, is based on the car system used in the top 10 rental companies in Hollywood to be modified, an increase of small

　　Car anti-turn system. 7075 high-quality aluminum alloy, ultra-hard oxidation.

　　5, the level of the car PTZ system can be adjusted third gear, the camera can be upside down, to facilitate your various needs.

　　6, high-quality air box, Pelican quality. Box design can accommodate 10 60CM track, to facilitate your standard basis

　　On the increase of two optional track. Air box with rod and pulley, one can easily pull away.

　　7, a variety of ways to use, the track can be placed directly on the ground or desktop use, but also the magic leg, lamp stand, tripod support.

camera viewfinder
gimbal tripod head
sevenoak tripod head
dslr camera cage
diy camera slider
shoulder camera rig
handheld video stabilizer
video camera stabilizer

Sevenoak Low Budget Camera Rig for your video

You must have tangled, go out with no camera rig? Without, in case you missed the beauty will regret. Take it, often back all day, the result did not use, physical exertion does not say that the passion of taking pictures greatly decreased. So small and lightweight tripod popular, but also the best alternative. This tripod bearing a small camera can be, if it is difficult to do the SLR. Is not there a camera rig both light and practical? Today Wolf family photography recommend a small and lightweight for you, you can respond to most of the shooting needs. Its foot tube material is very tough, strong plasticity, more load-bearing capacity! We measured a single foot bearing more than 2kg

Sometimes, the phone did not get steady, fall down and hit the eyes, that is called a painful eyes Venus! Side lying to play it, but also hurt the eyes, embarrassing, really awkward!

I know you have such a tangle, I also have such a tangled. So, today Bear brings a great bracket. With this it, no longer by the phone "pops" (smashing face).

Do not be scared by its huge body, in fact, it is not huge, nor heavy. Weight is not a bottle of mineral water Oh ~ but surprisingly easy to use!

　　Durable Mini Tripod camera rig SK-T1

　　The Sevenoak SK-T1 is a light weight and portable aluminum mini tripod designed for use with smartphones, action cameras and DSLRs. It comes with a small ball head, mini tripod and an extension tube. The small ball head makes it convenient for you to mount your device in a right position to take the best shoots. The mini tripod is designed with angle adjustment which enables you to change the angle of the feet easily.


The first time I use it, I fell in love with it, unable to extricate themselves. This PTZ cradle can be called a "cradle" compared to those used previously.

In fact, the most important thing is to use mobile phone holder is flexible. No matter how you lay, how to look at the phone, it can meet.

I used this plastic-type bracket, really bad! Easy to bend, too soft, simply could not hold the phone. Can support the phone, too hard, there is no strength to break the basic bend, breaking the desired angle. Later, abandon it!