What are the precautions for the grinding disc during installation?

The grinding with high quality grinding disc factory price is widely used for its excellent performance. The grinding disc plays an important role in industrial production. The correct installation of the grinding disc is directly related to the safety in the production process. Do you know the precautions for the grinding disc during installation? Below we Let's take a look at the relevant content.
 1. Before installing the grinding disc, the marking of the cutting piece with high quality grinding disc factory price must be checked first. The grinding disc with unclear or no marking must be re-tested by the rotation, otherwise it is easy to be confused.
2. We must understand the working line speed of the grinding disc. If the cutting piece with a working line speed of 50m/s is installed on a machine with a working line speed of 80m/s, it will easily break.
3. Before installation, use a wooden hammer to tap the grinding disc. If a crisp sound is heard, the grinding disc is qualified. Otherwise, there may be cracks in the grinding disc. This grinding disc cannot be used.
4. The flanges sandwiched on both sides shall have the same shape and shape. The diameter of the flange is generally half the diameter of the resin grinding disc, and the inner side shall have a concave groove. Between the end face of the grinding disc with high quality grinding disc factory price and the flange, a thickness shall be placed. Approximately 1 to 2 mm of elastic cardboard or leather, oil-resistant rubber gasket, the diameter of the gasket should be slightly larger than the outer diameter of the flange.
5. The flange screws should be tightened symmetrically in order to make the clamping force evenly distributed, but the force should not be too strong, otherwise one side will be fractured.
6. After the grinding disc with high quality grinding disc factory price is installed, it must be idling for one minute. This is for the last time to check the quality of the grinding disc. After the installation, the cutting piece must be carefully checked before use. It should work under high-speed rotation conditions. The installation must be secure and balanced. To avoid personal and quality accidents caused by cracks in some quality problems due to high speed operation.

The above is the relevant matters needing attention in the installation of the grinding disc, then our Henan Aurora Abrasive Tool Co., Ltd. specializes in grinding disc cutting, grinding disc ultra-thin, Henan abrasive grinding equipment special equipment development and production management business. For details, please consult high quality grinding disc factory price with us.

What is a fast cheap metal grinding disc

What is the fast cheap metal grinding disc? The classification of the cutting piece, the cutting piece belongs to the grinding disc and is made of abrasive and binder resin for ordinary steel, stainless steel metal, and non-metal material. With the development of the future machinery industry, the more The more cutting sheet industry is coming to this market, many companies have begun to update their product technology, hoping to develop more good products.

The fast cheap metal grinding disc is made of glass fiber and resin as the reinforced bonding material. It has high tensile strength, impact resistance, and bending strength. It is widely used in ordinary steel. Stainless steel metal and non-metal production and cutting materials, excellent materials. Exquisite craftsmanship guarantees different The high cutting efficiency and the best economic effect of the material workpiece. The fast cheap metal grinding disc classification is mainly divided into fiber resin grinding disc and diamond grinding disc according to the material.

In the face of the future, new fast cheap metal grinding disc will be more and more, then the hardness requirements of products that can be porridge are more and more, the hardness of the products that can be porridge can determine everything of the product, currently, by superhard abrasives High precision and high efficiency grinding results have been widely recognized.

The above is about the knowledge that can be used to open the porridge. If you want to know more knowledge about fast cheap metal grinding disc, you can pay attention to Henan Aurora Abrasive Tool Co., LTD. We specialize in the development and production of grinding discs and grinding discs.

The fast cheap metal grinding disc - precautions for use

In the industrial production and manufacturing, the fast cheap metal grinding disc sometimes needs to be used for certain grinding of the product, so it is necessary to use the corresponding equipment, and the use of the fast cheap metal grinding disc is to carry out some mechanical products. Grinding, it is an important abrasive tool that we need to use, but it is necessary to pay attention to the use of the appropriate method for operation, here are the safety precautions for the grinding disc.

The hardest part of the fast cheap metal grinding disc should be a diamond material, which is mainly composed of a base body and a cutter head. The base body is the main support part of the bonding cutter head, and the cutter head is a part that plays a cutting role during use. Need to pay attention to the process: when replacing the fast cheap metal grinding disc, first turn off the power supply, hang the warning sign, the cutting piece must be concentric, fasten, so as not to fall off and hurt people; when running, if the grinding disc is damaged, it must be stopped immediately, replace the good cutting piece Run again. After the cutting is completed, first turn off the power supply. When the fast cheap metal grinding disc stops rotating, take the object again to avoid the grinding disc from injuring people; it is strictly forbidden to sand the workpiece on the grinding disc.

The knowledge about the fast cheap metal grinding disc is introduced here. If you want to know more knowledge, you can pay attention to Zhengzhou Shuangling Abrasives Co., Ltd. We are specialized in grinding wheel cutting, grinding disc development and production management. We will Sincerely for your service, welcome new and old customers to come to buy.

High Quality Grinding Disc Production Process - Firing Process

The main working contents of the grinding process of the high quality grinding disc are: shaping before burning, placing the workpiece and vacuum firing.

The firing process of the high quality grinding disc is the most meticulous work of the brazing operator. To do this work, it is necessary to understand how the vacuum is built and how the temperature in the furnace thermal field changes. The principle of doing this work is: no solder can be placed in the non-welded place, the workpiece should be placed in the furnace, and strictly in accordance with the vacuum firing process.

Among them, the pre-burning shaping of the high quality grinding disc and the work of placing the workpiece are manually performed by one person. It takes 4 hours to complete the 500 grinding discs and share 4 working hours.

The vacuum firing of the high quality grinding disc is performed by a ZKR-3FH manual vacuum brazing furnace, which is usually performed manually by one person. It takes 12 hours to complete 500 grinding discs and share 12 working hours.

Classification of bonding agents for centerless grinding discs

There are three types of bonding agents commonly used in the high quality metal grinding discs:

1. Ceramic bond (code A). Ceramic binders are formulated from clay, feldspar and other natural silicates. These binders are abundant in the source, inexpensive, and have a wide range of applications. It can manufacture a variety of high-quality metal grinding discs with different particle size, hardness, structure, shape and size. It has stable performance, is not affected by climate and temperature, and is resistant to water, oil, acid and corrosion. It is suitable for grinding under various coolants. Dry grinding. The disadvantage is that it is brittle and does not tolerate severe vibration.

2. Resin binder (code S). The characteristics of this kind of bonding agent are high strength, high-speed grinding disc with a grinding line speed higher than 50 m/s and a very thin grinding disc; secondly, the combination with the abrasive grain is poor, and the high quality metal grinding disc made by the grinding disc is used. The grain is easy to fall off, and the grinding disc has good self-sharpness, so the grinding efficiency is low. However, the grinding disc wears quickly and is not easy to maintain the contour; the third is that there is a certain elasticity, and the contact surface between the high quality metal grinding disc and the workpiece is large, which not only increases the abrasive particles which are involved in cutting but also offsets part of the vibration, and is easy to obtain high smoothness. The disadvantage is that the corrosion resistance is poor, so the grinding disc made with it should not work under the reducing coolant, and the storage period should not be too long (limited to - year).

3. Rubber bond code X). It has a higher elasticity and a higher strength than the resin binder, and can be used to make a very large grinding disc. Since the rubber has good elasticity, the polishing effect is good during the grinding process, and high gloss is easily obtained. The disadvantage is that the high quality metal grinding disc is easy to wear, the shape of the grinding disc is poor, and because of the high density of the grinding disc, there is almost no air hole, and it is impossible to grind a lot of machining allowance, which is not suitable for rough grinding. At the same time, rubber has poor oil resistance and cannot be used as a coolant.

On the centerless grinding machine, the guide disc is mostly made of rubber bonding agent, and the grinding disc is mostly made of ceramic bonding agent. Sometimes, in order to improve the quality of grinding, the high quality metal grinding disc also uses a resin bond and a rubber bond.

At present, domestic high-speed grinding discs, although there are three kinds of bonding agents. However, at the time of manufacture, various additives are generally added to the binder. For example, alloying elements such as boron, lithium, barium and calcium are added to the ceramic bond grinding disc to improve the tensile strength of the bonding agent and ensure that the high quality metal grinding disc does not break at high speed.