200-125 試験関連情報 & 200-125 資格試験

NO.1 Which commands are required to properly configure a router to run OSPF and to add network
192.168.16.0/24 to OSPF area 0? (Choose two.)
A. Router(config-router)# network 192.168.16.0 0.0.0.255 area 0
B. Router(config)# router ospf 1
C. Router(config)# router ospf area 0
D. Router(config)# router ospf 0
E. Router(config-router)# network 192.168.16.0 0.0.0.255 0
F. Router(config-router)# network 192.168.16.0 255.255.255.0 area 0
Answer: A,B

200-125 予想   
Explanation:
In the router ospf command, the ranges from 1 to 65535 so o is an invalid number -> but
To configure OSPF, we need a wildcard in the "network" statement, not a subnet mask. We also need
to assgin an area to this process ->.

NO.2 Scenario
Refer to the topology. Your company has connected the routers R1, R2, and R3 with serial links. R2
and R3 are connected to the switches SW1 and SW2, respectively. SW1 and
SW2 are also connected to the routers R4 and R5.
The EIGRP routing protocol is configured.
You are required to troubleshoot and resolve the EIGRP issues between the various routers.
Use the appropriate show commands to troubleshoot the issues.
The loopback interfaces on R4 with the IP addresses of 10.4.4.4/32, 10.4.4.5/32, and
1 0.4.4.6/32 are not appearing in the routing table of R5. Why are the interfaces missing?
A. The loopback addresses haven't been advertised, and the network command is missing on R4.
B. Automatic summarization is enabled, so only the 10.0.0.0 network is displayed.
C. R4 has been incorrectly configured to be in another AS, so it does not peer with R5.
D. The interfaces are shutdown, so they are not being advertised.
Answer: C
Explanation:
For an EIGRP neighbor to form, the following must match:
- Neighbors must be in the same subnet
- K values
- AS numbers
- Authentication method and key strings
Here, we see that R4 is configured for EIGRP AS 2, when it should be AS 1.

NO.3 Which command can you use to test whether a switch supports secure connections and strong
authentication?
A. Switch#ssh -I admin 10.1.1.1
B. Switch>ssh -v 1-I admin 10.1.1.1
C. Router#ssh -v1 -I admin 10.1.1.1
D. Router>ssh -V2 -I admin 10.1.1.1
Answer: D

200-125 ブロンズ   

NO.4 Which command displays CPU utilization?
A. show process
B. show protocols
C. show version
D. show system
Answer: A

200-125 英語版   200-125 技術   
Explanation:
The "show process" (in fact, the full command is "show processes") command gives us lots of
information about each process but in fact it is not easy to read. Below shows the output of this
command (some next pages are omitted).
A more friendly way to check the CPU utilization is the command "show processes cpu history", in
which the total CPU usage on the router over a period of time: one minute, one hour, and 72 hours
are clearly shown:
+ The Y-axis of the graph is the CPU utilization.
+ The X-axis of the graph is the increment within the period displayed in the graph.
For example, from the last graph (last 72 hours) we learn that the highest CPU utilization within 72
hours is 37% about six hours ago.

Ciscoの認定試験は最近ますます人気があるようになっています。IT認定試験は様々あります。どの試験を受験したことがありますか。たとえば200-125 試験関連情報などです。これらは全部大切な試験です。どちらを受験したいですか。ここで言いたいのは200-125 試験関連情報です。この試験を受けたいなら、JapanCertの200-125 試験関連情報はあなたが楽に試験に合格するのを助けられます。

JapanCertの助けのもとで君は大量のお金と時間を费やさなくても復楽にCiscoの200-125 試験関連情報に合格のは大丈夫でしょう。ソフトの問題集はJapanCertが実際問題によって、テストの問題と解答を分析して出来上がりました。JapanCertが提供したCiscoの200-125 試験関連情報の問題集は真実の試験に緊密な相似性があります。

試験番号：200-125 絶対合格
試験科目：「CCNA Cisco Certified Network Associate CCNA (v3.0)」
最近更新時間：2017-05-15
問題と解答：572

>> 200-125 絶対合格

 

JapanCertは最新のHPE6-A41問題集と高品質の300-320問題と回答を提供します。JapanCertのC-TADM51-74 VCEテストエンジンと070-532試験ガイドはあなたが一回で試験に合格するのを助けることができます。高品質のC_TADM51_74 PDFトレーニング教材は、あなたがより迅速かつ簡単に試験に合格することを100％保証します。試験に合格して認証資格を取るのはそのような簡単なことです。

記事のリンク：http://www.japancert.com/200-125.html