ktestはCisco CCNP Wireless 300-360問題集試験のための便利なサービスを提供するために、非常に良いサイトです。
あなただけの模擬試験を行うために弊社のCisco CCNP Wireless 300-360 問題集問題集を取得する必要があり、あなたは成功に300-360試験に合格することができます。
弊社のCisco CCNP Wireless 300-360練習問題集を使用すると、常に高いレベルに到達するための独自の知識を向上させています。
弊社のCisco CCNP Wireless 300-360 問題集（Designing Cisco Wireless Enterprise Networks）試験資料は自分の知識と技能を高めることに助けになれることだけでなく、さまざまな条件であなたのキャリアを助けることもできます。
弊社のCisco CCNP Wireless資格 300-360受験対策を使って、10～20時間の独学だけで、お客様の時間と精力を節約して、一発合格が可能です。
試験番号 300-360
関連資格 CCNP Wireless
試験時間 90 分 (60 - 70 問)
試験言語 英語
試験登録 Pearson VUE
試験ポリシー 認定試験ポリシーおよび要件
試験チュートリアル 出題形式
300-360 Designing Cisco Wireless Enterprise Networks（WIDESIGN）は、CCNP Wireless 認定に関する試験であり、試験時間は 90 分、問題数は 60 〜 70 問です。この試験では、顧客とアプリケーションの要件の特定、予測ワイヤレス設計原則の適用、エンタープライズ ワイヤレス ネットワークの設計および最適化に必要なサイト調査の実施に関する知識が問われます。
12% 1.0 WLAN インストールに関連する
顧客要件を取得する
12% 2.0 WLAN 導入に関連する施設のタイプと制約事項を特定する
14% 3.0 WLAN の予測設計
14% 4.0 導入後のサイト調査
15% 5.0 導入後のサイト調査
15% 6.0 ワイヤレス ネットワークのインフラストラクチャを設計する
18% 7.0 リアルタイム アプリケーション用のワイヤレス アーキテクチャを説明し、設計する
A Cisco 7925 phone at a client¡¯s location is not registering with CUCM. The engineer analyzes a packet capture, sees that the phone receives an IP, and downloads the proper configuration file from TFTP successfully.
What type of messages should the phone be sending at this point?
A. H.245
B. H.323
C. MCGP
D. SCCP
Answer: D
After the completion of a site survey with Ekahau Site Survey tool, using the default color palette, it is noted that multiple areas are shown as white on the heat map when viewing 5 GHz signal strength data.
What does this indicate about the signal strength?
A. The area is below the minimum threshold configured on the tool.
B. The area is below the detectable level and indicates no RF signal.
C. The area is below -100 dBm at coverage cell edge.
D. The area is below -67 dBm at coverage cell edge.
Answer: A
An engineer must design wireless coverage in thick-walled stairwells.
Which information should the engineer refer to when determining where APs can be installed?
A. Local or National Building Code
B. IEEE
C. BICSI TDMM
D. Cisco Hardware Installation Guide
Answer: A
An engineer is performing a predictive wireless design for a medical treatment environment, which requires data and voice services.
Which of the following is a requirement for the design?
A. overlapping -72 dBm coverage from two access points
B. overlapping -67 dBm coverage from two access points
C. continuous -67 dBm coverage from one access point
D. continuous -72 dBm coverage from one access point
Answer: C
A network engineer is preparing for an office site survey with a height of 2.5 meters.
Which three components are recommended to complete the survey? (Choose three.)
A. Use APs with external antennas.
B. Use DoS attack on APs while measuring the throughput.
C. Use APs with built-in antennas.
D. Use a battery pack to power APs.
E. Use a drawing of the office space to draw AP and client placements.
F. Use APs with directional antennas.
Answer: C,D,E
An engineer is planning for a 24 Mbps data rate for a new installation.
What is the coverage area from the AP if the environment and other factors are not taken into consideration?
A. 225 feet
B. 80 feet
C. 150 feet
D. 100 feet
Answer: B
Which two options describe best practices that must be completed after a wireless installation is finished? (Choose two.)
A. Make sure that there are no spaces between the devices on the rack that the Wireless Lan Controller is installed.
B. Consult with the customer to ensure that the IT staff has a complete set of design and installation documents.
C. Make sure the customer is aware that they should consider purchasing a support contract immediately after the installation is complete.
D. Spend time with the customer to show them the controller GUI and inform them how they can reach the Cisco TAC if they have any problems.
E. Test all the customer¡¯s wireless devices and applications to ensure they are working properly.
Answer: B,E
What is a common cause for signal attenuation?
A. Cinder block wall
B. Office window
C. Metal door
D. Glass wall
Answer: C
The AP has been configured property for a VoWLAN survey The RF environment contains a noise of -87 to -90 dBm.
What is the target value for the cell edge reading?
A. -62 dBm
B. -67 dBm
C. -60 dBm
D. -70 dBm
Answer: B
An 802.11n implementation is being discussed. Users are satisfied with the potential 300450 Mbps throughput of new 802.11n APs.
Which three bandwidth requirements are used to calculate per client bandwidth through an 802.11n AP network? (Choose three.)
A. 450 Mbps throughput is the client max for 5-GHz radio.
B. Channel bonding on 5 GHz is required for a client to have a 300 Mbps WiFi link.
C. 300 Mbps throughput is the client max for 2.4-GHz radio.
D. The remaining bandwidth is divided per device when more clients are connected to one AP.
E. 100 Mbps Ethernet switch port is a potential bottleneck.
F. Clean Air helps clear noise for 802.11n channel bonding to work.
Answer: A,C,E
An engineer is performing a predictive wireless design for a carpeted office space, which requires voice capability and location services.
Which two requirements are inputs to the design? (Choose two.)
A. overlapping -67 dBm coverage from three access points
B. overlapping -75 dBm coverage from three access points
C. overlapping-72 dBm coverage from two access points
D. continuous -67 dBm coverage from one access pointe. continuous -72 dBm coverage from one access point
Answer: BD
You have a customer that is building a new campus of four 3-story buildings that you have just completed the site survey for. The customer is interested in the mount of rack space they will need to allocate in either the building MDF or in the data center for controllers. Each building is going to require 75 APs to support voice and data.
How should the controllers be deployed to provide the least number of controllers, the highest redundancy, and the easiest management?
A. Use the centralized deployment method in the data center with the N + N redundancy method.
B. Use the centralized deployment method in the data center with the N + 1 redundancy method
C. Use the centralized deployment method in the data center with the 1 + 1 redundancy method and clients SO.
D. Use the distributed deployment method in each building MDF with the N + 1 redundancy method.
E. Use the distributed deployment method in each building MDF with the N + N + 1 redundancy method.
F. Use the distributed deployment method in each building MDF with the N + N redundancy method.
Answer: B
あなただけの模擬試験を行うために弊社のCisco CCNP Wireless 300-360 問題集問題集を取得する必要があり、あなたは成功に300-360試験に合格することができます。
弊社のCisco CCNP Wireless 300-360練習問題集を使用すると、常に高いレベルに到達するための独自の知識を向上させています。
弊社のCisco CCNP Wireless 300-360 問題集（Designing Cisco Wireless Enterprise Networks）試験資料は自分の知識と技能を高めることに助けになれることだけでなく、さまざまな条件であなたのキャリアを助けることもできます。
弊社のCisco CCNP Wireless資格 300-360受験対策を使って、10～20時間の独学だけで、お客様の時間と精力を節約して、一発合格が可能です。
試験番号 300-360
関連資格 CCNP Wireless
試験時間 90 分 (60 - 70 問)
試験言語 英語
試験登録 Pearson VUE
試験ポリシー 認定試験ポリシーおよび要件
試験チュートリアル 出題形式
300-360 Designing Cisco Wireless Enterprise Networks（WIDESIGN）は、CCNP Wireless 認定に関する試験であり、試験時間は 90 分、問題数は 60 〜 70 問です。この試験では、顧客とアプリケーションの要件の特定、予測ワイヤレス設計原則の適用、エンタープライズ ワイヤレス ネットワークの設計および最適化に必要なサイト調査の実施に関する知識が問われます。
12% 1.0 WLAN インストールに関連する
顧客要件を取得する
12% 2.0 WLAN 導入に関連する施設のタイプと制約事項を特定する
14% 3.0 WLAN の予測設計
14% 4.0 導入後のサイト調査
15% 5.0 導入後のサイト調査
15% 6.0 ワイヤレス ネットワークのインフラストラクチャを設計する
18% 7.0 リアルタイム アプリケーション用のワイヤレス アーキテクチャを説明し、設計する
A Cisco 7925 phone at a client¡¯s location is not registering with CUCM. The engineer analyzes a packet capture, sees that the phone receives an IP, and downloads the proper configuration file from TFTP successfully.
What type of messages should the phone be sending at this point?
A. H.245
B. H.323
C. MCGP
D. SCCP
Answer: D
After the completion of a site survey with Ekahau Site Survey tool, using the default color palette, it is noted that multiple areas are shown as white on the heat map when viewing 5 GHz signal strength data.
What does this indicate about the signal strength?
A. The area is below the minimum threshold configured on the tool.
B. The area is below the detectable level and indicates no RF signal.
C. The area is below -100 dBm at coverage cell edge.
D. The area is below -67 dBm at coverage cell edge.
Answer: A
An engineer must design wireless coverage in thick-walled stairwells.
Which information should the engineer refer to when determining where APs can be installed?
A. Local or National Building Code
B. IEEE
C. BICSI TDMM
D. Cisco Hardware Installation Guide
Answer: A
An engineer is performing a predictive wireless design for a medical treatment environment, which requires data and voice services.
Which of the following is a requirement for the design?
A. overlapping -72 dBm coverage from two access points
B. overlapping -67 dBm coverage from two access points
C. continuous -67 dBm coverage from one access point
D. continuous -72 dBm coverage from one access point
Answer: C
A network engineer is preparing for an office site survey with a height of 2.5 meters.
Which three components are recommended to complete the survey? (Choose three.)
A. Use APs with external antennas.
B. Use DoS attack on APs while measuring the throughput.
C. Use APs with built-in antennas.
D. Use a battery pack to power APs.
E. Use a drawing of the office space to draw AP and client placements.
F. Use APs with directional antennas.
Answer: C,D,E
An engineer is planning for a 24 Mbps data rate for a new installation.
What is the coverage area from the AP if the environment and other factors are not taken into consideration?
A. 225 feet
B. 80 feet
C. 150 feet
D. 100 feet
Answer: B
Which two options describe best practices that must be completed after a wireless installation is finished? (Choose two.)
A. Make sure that there are no spaces between the devices on the rack that the Wireless Lan Controller is installed.
B. Consult with the customer to ensure that the IT staff has a complete set of design and installation documents.
C. Make sure the customer is aware that they should consider purchasing a support contract immediately after the installation is complete.
D. Spend time with the customer to show them the controller GUI and inform them how they can reach the Cisco TAC if they have any problems.
E. Test all the customer¡¯s wireless devices and applications to ensure they are working properly.
Answer: B,E
What is a common cause for signal attenuation?
A. Cinder block wall
B. Office window
C. Metal door
D. Glass wall
Answer: C
The AP has been configured property for a VoWLAN survey The RF environment contains a noise of -87 to -90 dBm.
What is the target value for the cell edge reading?
A. -62 dBm
B. -67 dBm
C. -60 dBm
D. -70 dBm
Answer: B
An 802.11n implementation is being discussed. Users are satisfied with the potential 300450 Mbps throughput of new 802.11n APs.
Which three bandwidth requirements are used to calculate per client bandwidth through an 802.11n AP network? (Choose three.)
A. 450 Mbps throughput is the client max for 5-GHz radio.
B. Channel bonding on 5 GHz is required for a client to have a 300 Mbps WiFi link.
C. 300 Mbps throughput is the client max for 2.4-GHz radio.
D. The remaining bandwidth is divided per device when more clients are connected to one AP.
E. 100 Mbps Ethernet switch port is a potential bottleneck.
F. Clean Air helps clear noise for 802.11n channel bonding to work.
Answer: A,C,E
An engineer is performing a predictive wireless design for a carpeted office space, which requires voice capability and location services.
Which two requirements are inputs to the design? (Choose two.)
A. overlapping -67 dBm coverage from three access points
B. overlapping -75 dBm coverage from three access points
C. overlapping-72 dBm coverage from two access points
D. continuous -67 dBm coverage from one access pointe. continuous -72 dBm coverage from one access point
Answer: BD
You have a customer that is building a new campus of four 3-story buildings that you have just completed the site survey for. The customer is interested in the mount of rack space they will need to allocate in either the building MDF or in the data center for controllers. Each building is going to require 75 APs to support voice and data.
How should the controllers be deployed to provide the least number of controllers, the highest redundancy, and the easiest management?
A. Use the centralized deployment method in the data center with the N + N redundancy method.
B. Use the centralized deployment method in the data center with the N + 1 redundancy method
C. Use the centralized deployment method in the data center with the 1 + 1 redundancy method and clients SO.
D. Use the distributed deployment method in each building MDF with the N + 1 redundancy method.
E. Use the distributed deployment method in each building MDF with the N + N + 1 redundancy method.
F. Use the distributed deployment method in each building MDF with the N + N redundancy method.
Answer: B