Sorry , i am Dustin from Taiwan . One more question , after change the spacer , then change eibach lower spring ...... The tire will chafe on the edge of car body , when you face a serious shock ?
i would like to change spacer + eibach spring . (as your idea)
Regards
Dustin
台湾の人・・・。 (ロク)
2006-12-23 07:24:20
この人多分サクラムさんにもRSのエキゾーストの注文をした人です。
ディラーさんではないみたいですよ。 カブチャンお答えしてあげて!
Thank you about your question! (cubra)
2006-12-25 08:56:07
Good morning Mr? Dustin!
My name is Cubra! a.k.a. meganiste funky driver!
well,I gonna tell the spacers specs.
>front :10mm Yes!
>rear:25mm Yes!
>center hole diameter ?
Sorry I'm not sure about it so I will ask Mr.ロク!(He gave comment below & made my spacers)Please wait untill ask him .
>the other 5 holes diameter ? yes it's 5holes.
>5H/100 ? 110 ? Megane RS's P.C.D is 108mm. and also the offset of the wheel is 68mm
>Material is aluminum ? Yes, he said that have very high accuracy!
OK? Dustin? now I will answer next questions!
>One more question・・・・・OK!!
>after change the spacer , then change eibach lower spring ......
yes it's my modify way! but There is no reason about it. It's just timing.
>The tire will chafe on the edge of car body , when you face a serious shock ?
I don't think that you may worry because the tire never hits the edge of the body.
>i would like to change spacer + eibach spring .
Oh! I also think it's a nice idea ! I think spacer+eibach is the only way for nice modify for our megane RS!
Dustin! It is at Mr. Roku that developed spacer and eibach of the misunderstanding who gave the comment below though it is told not to be. By the way his blog is http://blogs.yahoo.co.jp/osamubmwe36m3b He is my teacher of megane modify.
Please question again if you do not understand because of my poor English.
I had ordered the eibach lower spring from TWN agent.But now no stock , need waitting till next Feb. And about spacer , i will special survey with TWN vendor as your spec . It is very lucky to me , to see your blog , to get such useful tuning information . ^_^
Again , thanks a lot .
Dustin
Ps. now i try to find the "Valeo" soft wiper from TWN market..... ha ~~~
Hi~ i just checked the H&R web site as below . http://www.baneya.jp/h&r-spacer_bolt&nut.html but for front , no 10mm type ?! It means the spacer of Cubra san 's RS was hand made ?! not by H&R ? And the originial bolt need to change new type ?
Dustin .
for Dustin! (cubra)
2006-12-26 19:03:46
Good evening Dustin!!
sorry,I have no time to answer for your quistions now.(TT)
but I can answer it tomorrow!so please wait a little bit more.
sorry!
well (cubra)
2006-12-26 23:16:23
Hello Dustin!
This is cubra ! now i'm back!!! (^^;
Firstly I say about megane's hub center bore diameter.
actually I cannot confirm about that! and Mr.roku said "forgot already!(^^;" so it's very sorry about that.
By the way Your asking My spacer had made by Mr.roku. and Mr.roku-san was order it specially for Professional Racing-parts builder(sorry I don't know where that is).
so My spacer is just only one.
Last time I said "Yes, he said that have very high accuracy!"meant that.
Because this spacer has made the allowance from 0, it is not easy to install it very much. However, spacer installed in Megarnu was to have wanted you to know making by thinking it to be a rotation part like that because it was very thick.
It is said that the risk is high if the one with very high accuracy is not chosen if spacer of 25mm in rear is installed.
and bolt for my spacer is also made by Mr.roku. and I don't know the specs・・・・・
If you want to make same bolt&spacer then I can ask Roku-san about the shops.
Please comment by all means though it apologizes very much like being not able to help you at all if there is a question again.
Thanks for your greeting of earthquake matter . I live in Taipei. so it is ok . As news report , the south of Taiwan was have more serious damage. >_< While it happened , my wife and me was watching tv , we can feel it , but think it's not so serious ..... as you know , Taiwaness have many many experiences for big earthquake , so we had been trained to be used to something .(くしょうする)
About spacer ....... I will check it out with Taiwan vendor (or agent)first ..... , if no good news , mai i call help from you and Roku san !? ^___^
Dustin .
It was good. (cubra)
2006-12-27 14:19:09
The earthquake may be not awful in taipei
It is nowadays because the earthquake has not come for a long time in Miyazaki Prefecture where I live of forgetting completely though there is considerably an earthquake also in Japan.
Please always contact something also the matter of spacer when is. If it is possible to help, I will help.
これでカレーを食べにいけますね
次はマフラーですか、パーツがあって羨ましいです。
その前に先立つものがありませんが・・・。
カレーってどこまで行くんですか〜?
現場検証並みに写真取まくり。
cubraです。
ubarさん。
ええ、行けますとも
《》Manmaさん。
案外、グラセニでもいけるかも知れませんよ。
ただ、サイズが市販であるのか・・・リアはあそこまで
カレーは、《》Manmaさんのいらっしゃる「そこ」までです。
蒼き狼さん。
おおぅ、コメント4連発!
現場検証しましょうね
探してみます。
カレーってココまでですか〜?
私たちもGW前半に九州方面に行く予定があります。
「瞼の君」にやっと会えるんですね。
cubraさんのインプレを見ていたら、すっごく欲しくなってきました
cubraさんのインプレを見ていたら、すっごく欲しくなってきました
タイヤはアライメントを取りなおせばワイドトレッドにされても
減りません。
キャンバつきすぎる(見てないけど・・)のは
私信しますね、簡単な理由です。
一般市販品のスペーサーはフロントにはお勧めしません。
絶対に汎用スペーサーはフロントには使用しないで下さいこのスペーサーはRS専用のワンオフ品です。
ご興味の方は製造元を教えますのでご自分で注文下さい。もちろん僕もcubraさんもマージンとってません(笑)
因みにフロントセットで4万円ボルト1本1000円です。
リアは8万円ボルトは特注1本2000円です。
その代わり精度抜群交差0で装着も脱着も素人は手を出さないほうが良いでしょう。
GT500のレーシングカーの部品を製作している会社に
依頼しましたので品物は最高級品です。
装着するとどんな感じかはcabraさんの文章で
ご想像ください(笑)
「瞼の君」?辞書に載ってないんです
「
GWにQ州に再上陸なのですね。お会い出来たらいいなぁ・・出来なくても、今年こそ絶対にカレーはたべにいきますね
てんぷちさん。
スペーサーで乗り心地が良くなって、「めい」ちゃんも大喜び
ロクさん。
いつもいつも補足ありがとうございます。
今日お電話でおはなしした話題も・・
でした。えへへ。
という、わけで、ロクさんのコメントにあるとおり、フロントはよっぽど精度良く作られている物でないと・・???かもしれません。
皆様スペーサーを噛まされるときは気を付けましょう
「おいら瞼を閉じればいつでもおっかさんに会えるんでぇ〜」
そんな感じでしょうか?
同じ趣味の世界にいながら中々会えないcubraさんは「瞼の君」なんですよ〜。モーホーの趣味はありませんのでご安心ください(笑
そうです、「瞼の母」は辞書にも載っておりました。
そういう意味ですか。えへへ。
ぼくも、モーホーさんではないので安心ですよ。
ということなら、《》Manmaさんは私にとっても「瞼の大王」です。お会いしてみたいぃっ
これで中華食べに来られますね!
パクリマシタ :-)
でも、要注意なのは、速度域だよね…。cubraさんの思っている「高速」と他の人の「高速」はキット違う。;-)
うちのRanaは「高速」ではバタバタです (;_;)
バネと、サイレンサーが変わったら、是非
ちなみに、cubraの定義する高速とは「100km/hから150km/h」ですが・・・異常でしょうか?
miyaさんに、「異常だよ!」とか言われると・・・異議あり
rear:25mm
center hole diameter ?
the other 5 holes diameter ?
5H/100 ? 110 ?
Material is aluminum ?
One more question , after change the spacer , then change eibach lower spring ......
The tire will chafe on the edge of car body , when you face a serious shock ?
i would like to change spacer + eibach spring .
(as your idea)
Regards
Dustin
ディラーさんではないみたいですよ。
カブチャンお答えしてあげて!
My name is Cubra! a.k.a. meganiste funky driver!
well,I gonna tell the spacers specs.
>front :10mm
Yes!
>rear:25mm
Yes!
>center hole diameter ?
Sorry I'm not sure about it so I will ask Mr.ロク!(He gave comment below & made my spacers)Please wait untill ask him .
>the other 5 holes diameter ?
yes it's 5holes.
>5H/100 ? 110 ?
Megane RS's P.C.D is 108mm.
and also the offset of the wheel is 68mm
>Material is aluminum ?
Yes, he said that have very high accuracy!
OK? Dustin? now I will answer next questions!
>One more question・・・・・OK!!
>after change the spacer , then change eibach lower spring ......
yes it's my modify way! but There is
no reason about it. It's just timing.
>The tire will chafe on the edge of car body , when you face a serious shock ?
I don't think that you may worry because the tire never hits the edge of the body.
>i would like to change spacer + eibach spring .
Oh! I also think it's a nice idea !
I think spacer+eibach is the only way for nice modify for our megane RS!
Dustin! It is at Mr. Roku that developed spacer and eibach of the misunderstanding who gave the comment below though it is told not to be. By the way his blog is
http://blogs.yahoo.co.jp/osamubmwe36m3b
He is my teacher of megane modify.
Please question again if you do not understand because of my poor English.
The question from you was very glad.
ちなみにセンターボアの径ってば、どれ位でしたっけ?
Thanks for your kindly and quickly reply .
I had ordered the eibach lower spring from TWN agent.But now no stock , need waitting till next Feb.
And about spacer , i will special survey with TWN vendor as your spec .
It is very lucky to me , to see your blog , to get such useful tuning information . ^_^
Again , thanks a lot .
Dustin
Ps. now i try to find the "Valeo" soft wiper from TWN market..... ha ~~~
駅前留学してんの?
それとも、家のテレビで先生がでてくるやつ?
ま、冗談はさておき、ハブセンターのピッチは
『忘れました』
ちょっと前まではデータ採ってありましたが、
消しちゃった(笑)
ごめんなさいです。
Megane Sport Typ M(165kw) 108/5 60.1 M14x1.5
cubraサン、pdf直送しましょうか!?
カブちゃん号のワイドスペーサーはH&Rとはピッチが
異なります。
というのも、余りにも『肉厚』な為、重量が嵩みます。
ゼロ公差にしないと高回転時にブレが
起こりハンドリングに影響します。
カブちゃんの装着時の画像や小生の駄文をご覧戴ければ
お解り頂ける?(かどうかわかりませんが)トニカク
外すのも、着けるのも、大変なくらい(特にリア)の精度
です。
でも、多分近い数値だったきもするなぁ・・。
カブちゃん『自分で測ってよ〜』って返事しておいて(笑)
i just checked the H&R web site as below .
http://www.baneya.jp/h&r-spacer_bolt&nut.html
but for front , no 10mm type ?!
It means the spacer of Cubra san 's RS was hand made ?! not by H&R ?
And the originial bolt need to change new type ?
Dustin .
sorry,I have no time to answer for your quistions now.(TT)
but I can answer it tomorrow!so please wait a little bit more.
sorry!
This is cubra !
now i'm back!!!
(^^;
Firstly I say about megane's hub center bore diameter.
actually I cannot confirm about that!
and Mr.roku said "forgot already!(^^;" so
it's very sorry about that.
By the way
Your asking My spacer had made by Mr.roku.
and Mr.roku-san was order it specially for Professional Racing-parts builder(sorry I don't know where that is).
so My spacer is just only one.
Last time I said "Yes, he said that have very high accuracy!"meant that.
Because this spacer has made the allowance from 0, it is not easy to install it very much. However, spacer installed in Megarnu was to have wanted you to know making by thinking it to be a rotation part like that because it was very thick.
It is said that the risk is high if the one with very high accuracy is not chosen if spacer of 25mm in rear is installed.
and bolt for my spacer is also made by Mr.roku.
and I don't know the specs・・・・・
If you want to make same bolt&spacer then I can ask Roku-san about the shops.
Please comment by all means though it apologizes very much like being not able to help you at
all if there is a question again.
I'm worry about Earthquake@taiwan
Are you OK?
Thanks for your greeting of earthquake matter .
I live in Taipei. so it is ok .
As news report , the south of Taiwan was have more serious damage. >_<
While it happened , my wife and me was watching tv , we can feel it , but think it's not so serious ..... as you know , Taiwaness have many many experiences for big earthquake , so we had been trained to be used to something .(くしょうする)
I will check it out with Taiwan vendor (or agent)first ..... , if no good news , mai i call help from you and Roku san !? ^___^
Dustin .
It is nowadays because the earthquake has not come for a long time in Miyazaki Prefecture where I live of forgetting completely though there is considerably an earthquake also in Japan.
Please always contact something also the matter of spacer when is. If it is possible to help, I will help.