Fiber Optic Tech

Sharing various fiber optic news, inforamtion, topics, etc.

High-density QSFP+ SR4 Transceiver Cabling Methods

2016-10-18 10:19:28 | 40 Gigabit Ethernet

With the increasing demand for higher speed in fiber optic communications, 40G network is widely deployed in today’s backbone transmission network. 40G QSFP+ SR4 transceivers, for short reach applications, can support distance of up to 150 m over OM4 multimode optical fiber. Inserted in switch, QSFP+ SR4 module utilizes a MTP/MPO interface for dual way transmission.

There are a lot of methods to connect QSFP+ SR4 transceivers to other devices by using different connectivity products. Besides, the cabling for 40G is relatively more difficult than that of 10G network, which requires more cables and space. Here are several high density QSFP+ SR4 transceiver cabling methods.

40gb QSFP+

QSFP+ SR4 40G to 40G Applications

40G to 40G transmission is needed in a 40G fiber optic network. The following picture simply illustrates how 40G to 40G multimode transmission is being achieved by QSFP+ SR4 transceivers. Two QSFP+ SR4 modules interconnected with a MTP trunk cable are separately inserted into two switches. Thus two switches are linked successfully.

40G Cabling

Of course, there are also other ways to achieve this connection. The more devices you use, the more complex it is to achieve connections because cable counts increase. As shown in the following figure, a 48-port 1U rack mount MTP fiber patch enclosure is used. Four 12-port MTP fiber adapter panels can be deployed in this standard 1U rack mount enclosure. With the help of this 48-port MTP fiber enclosure, cable management for 40G connections could be easier.

40G high-density cabling

QSFP+ SR4 40G to 10G Applications

QSFP+ SR4 is a parallel fiber optic transceiver which uses four fibers for transmitting and four fibers for receiving at the same time. The 40G fiber optic signal can be separated into four 10G signals to meet the 40G to 10G transferring requirements. The fiber optic cable count will be increased at the 10G distribution end. Usually a breakout MTP-8LC harness cable is used. For better cable management, a 1U 96-fiber enclosure is recommended, which includes four HD MTP cassettes transferring MTP front the 40G end to LC at the 10G end. Four 10G-SR SFP+ modules, inserted in 10G switch/ports, can be connected to the corresponding LC ports on fiber optic enclosures to achieve the duplex transmission between 40G and 10G.

For higher cabling density, the above mentioned 48-port 1U rack mount MTP fiber patch enclosure is still being recommended, which can provide high density 40G MTP cabling environment. And additional MTP-8LC harness cables should be used for transferring signals between 40G and 10G.

Conclusion

Through the above analysis we can see that, QSFP+ SR4 transceivers can meet various cabling applications with different fiber products. Apart from the above-mentioned methods, there are also others way to build connections using QSFP+ SR4 modules and it will depend on the practical applications and cabling environments. All the related products for the above mentioned methods can be found in FS.COM.

ジャンル:
ウェブログ
コメント   この記事についてブログを書く
この記事をはてなブックマークに追加
« Common Types of Fiber Optic... | トップ | How to Choose the Right Fib... »

コメントを投稿


コメント利用規約に同意の上コメント投稿を行ってください。

数字4桁を入力し、投稿ボタンを押してください。

あわせて読む

トラックバック

この記事のトラックバック  Ping-URL
  • 30日以上前の記事に対するトラックバックは受け取らないよう設定されております。
  • 送信元の記事内容が半角英数のみのトラックバックは受け取らないよう設定されております。
  • このブログへのリンクがない記事からのトラックバックは受け取らないよう設定されております。
  • ※ブログ管理者のみ、編集画面で設定の変更が可能です。