以前、工房のお手伝いでカップに付くハンドルを作っておりました。
ハンドルは、何個も同じものを、形をたがえずにつくる必要があるので、
石膏型に粘土をはめ込んで、ぎゅうぎゅう形になるように押し込み、成形していきます。
これが型で起こしたハンドル。
ずらずらずら~。
これで必要な量の半分。
そして余計な土などを取り除いて形を整え、乾かないようにコンテナに詰めて工房へ
そこから、水挽して削られたカップとドッキングして乾燥・素焼き・釉薬をかけ窯に入れられる。
これが焼き上がり
おっと! 君たちいい感じの手になっているねぇ
どれどれ。
手になじむね~。
型があるとはいえ、微調整は必要。手間はかなりかかっているんです。
皆様に格好イイ器を届けたいですから、それはもう超頑張っているんですよ~。
さぁ、次は何を格好良くするため頑張ろうかな~(笑)
7月15日、新店舗がオープンしますので見に来てくださいね。
お待ちしております。
- * - * - * - * - * -
Previously, I was making a handle attached to the cup.
Since it is necessary to handle the same handle without touching the same shape,
Place the clay in the plaster mold, push it in the form of a handle and mold it.
This is a handle caused by a mold.
Staggering slack ~ ~.
This is half of the required amount.
Then remove the extra clay and shape it, pack it in a container so that it does not dry, and bring it to the factory.
From there, dock with a cup that has been sharpened by water, dry, unglazed, glazed and put in a kiln and bake.
This baked.
Oops! You guys (that's a handle) It's got a nice feeling.
let's see.
I will fit in my hands.
Even though there are molds, fine adjustment is necessary. It takes a lot of time and labor.
I want to deliver a good-looking instrument to everyone, so it's already working hard.
Well, next time I'll do my best to make it look good - (lol)
A new store will open on 15th July.
I am looking forward to your coming to Asahi-yaki.
ハンドルは、何個も同じものを、形をたがえずにつくる必要があるので、
石膏型に粘土をはめ込んで、ぎゅうぎゅう形になるように押し込み、成形していきます。
これが型で起こしたハンドル。
ずらずらずら~。
これで必要な量の半分。
そして余計な土などを取り除いて形を整え、乾かないようにコンテナに詰めて工房へ
そこから、水挽して削られたカップとドッキングして乾燥・素焼き・釉薬をかけ窯に入れられる。
これが焼き上がり
おっと! 君たちいい感じの手になっているねぇ
どれどれ。
手になじむね~。
型があるとはいえ、微調整は必要。手間はかなりかかっているんです。
皆様に格好イイ器を届けたいですから、それはもう超頑張っているんですよ~。
さぁ、次は何を格好良くするため頑張ろうかな~(笑)
7月15日、新店舗がオープンしますので見に来てくださいね。
お待ちしております。
- * - * - * - * - * -
Previously, I was making a handle attached to the cup.
Since it is necessary to handle the same handle without touching the same shape,
Place the clay in the plaster mold, push it in the form of a handle and mold it.
This is a handle caused by a mold.
Staggering slack ~ ~.
This is half of the required amount.
Then remove the extra clay and shape it, pack it in a container so that it does not dry, and bring it to the factory.
From there, dock with a cup that has been sharpened by water, dry, unglazed, glazed and put in a kiln and bake.
This baked.
Oops! You guys (that's a handle) It's got a nice feeling.
let's see.
I will fit in my hands.
Even though there are molds, fine adjustment is necessary. It takes a lot of time and labor.
I want to deliver a good-looking instrument to everyone, so it's already working hard.
Well, next time I'll do my best to make it look good - (lol)
A new store will open on 15th July.
I am looking forward to your coming to Asahi-yaki.